Shiv Sons

Bostik Lw Integral Waterproofing Admixture For Concrete And Plaster
Bostik lw is a chloride free admixture and supplied as brown liquid.

Areas Of Application:

- concrete roof slab.
- floor screeds in bathroom and damp areas.
- basement slabs and walls.
- concreting / internal plastering compliance - is2645-2003.

Dosage:

- 200 ml per 50 kg. Cement.

Packaging:

- 200ml,1,5,10,20,100 & 200 litre.

Storage & Shelf Life:

- 12 months.

Bostik Seal N Flex 1 is a lowmodulus, one component, Class-A polyurethane sealant. When cured it will form a tough and flexible seal capable of cyclic expansion and compression movement of 100% (0%) of the original installed joint width. Bostik Seal N Flex 1 can be used on: Insitu concrete and render, Precast and tilt up panels Brickwork and block work, Plasterboard face and paper lined recessed edges, Fibre cement sheet, Aluminium windows, Granite, sandstone & marble, GRC, fiberglass and mostly specialty panel systems.

Bostik ERM is a solvent free three component screed mortar based on epoxy resin

USE

1.Industries like fertilizers, paper and textiles.
2.Highways and Airport runways.
3.Water treatment and sewage treatment plants. 
4.To repair flooring crack and patch works.
5.To fill the gap between metal and concrete in flooring Coving application.

ADVANTAGES

Fast setting
Good mechanical properties
Negligible strength
Solvent free 

Bostik Two in One is a chloride free integral water proofing and water reducing admixture forplaster and concrete

Recommended Uses

• Concrete roofslabs
• Floorscreed in bathroom and damp areas
• Basement slabs and walls
• Concreting /Plastering ofwatertanks and sumps
• External/Internalplastering

Features and benefits

• Increases workability and improves placing & compaction ofconcrete
• Blocks the capillarystructure within concrete
• Improves durabilityand compressive strength
• Improves cohesion and prevents segregation of concrete 

COLD APPLIED POLYURETHANE SEALANT

Seal `N'' Flex 1 is a low modulus, one component, Class-A polyurethane sealant. When cured it will form a tough, flexible seal capable of cyclic expansion and compression movement of 100% (± 50%) of the original joint width. CLASSIFICATION STANDARDS • CSIRO RILEM Long - Term Sealant Durability Study DBCE Doc.97/196 (M) • DIN 18540 (German) and SJNF (French) approval as a low modulus external joint sealant • AS 4020 Potable Water • ASTM C.920-87 & 98 (USA) as Type S, Grade NS, Class 50, use NT, G, A, M & O as an external joint sealant. • AS 1157-1972 Resistance to fungal growth. Ministry of Agriculture and fisheries New Zealant (Meat, Fish, Game, Poultry - All areas)

Bostik H785 HIGH TACK is a high quality professional hybrid adhesive with an extremely high initial tack. Bostik H785 HIGH TACK fulfil BREEAM specifications mentioned in chapter ‘Health and Wellbeing’, Hea 02 Indoor Air Quality, regarding volatile organic compound (VOC) emission levels (products). 

APPLICATIONS

Bostik H785 HIGH TACK was specifically developed as a universal high grip and high strength adhesive for bonding many building materials such as: stone, concrete, mirrors, glass, plasterboard, PU, PVC, hard plastics, enamel, ceramic, copper, lead, zinc, tin, aluminium, metals, alloys, stainless steel, HPL and cement fibre panels (* ) and wood. * for panel bonding Bostik is offering the H970 PANELTACK MM, H975 PANELTACK HM and S970 ROCKPANEL S. 

DIRECTIONS OF USE

Apply adhesive with the provided V-nozzle in a 'ventilating way' in vertical stripes with 10 - 20cm distance between stripes. Bring the materials into position and press firmly so that the adhesive is a minimum of 2 - 3mm thick between material and surface. Do not apply the adhesive in dots! Because of the high initial strength, support during curing is usually not necessary. For further questions please contact our technical department.

Bostik P590 Seal’n’flex One Plus Is A New Generation One Component Low Modulus Professional High Quality And Durable Polyurethane Sealant Which Cures Under Influence Of Humidity To Form A Durable Elastic Bubble Free Seal. Applications Bostik P590 Seal’n’flex One Plus Is Has Been Developed As A High Quality Sealant For All Kind Of Connection And Expansion Joints Many Common Building Materials, Such As In Concrete, Wood, Metal, Aluminium And Pvc Frames, Masonry And Even Natural Stone, Granite And Marble. Directions Of Use A Joint With The Correct Dimensions Is Able To Absorb Movements Between Building Materials. The Joint Depth Should Always Be In The Correct Relationship Of The Joint Width. A General Rule Is The Ratio Of Joint Depth To The Width Of The Joint With A Joint Width Up To 10mm Is 1:1, With A Minimum Of 5mm In Width And Depth. For Joints Wider Than 10mm, The Depth Is The Width Divided By 3 Plus 6mm.

Limitations - Not Suitable For Pe, Pp, Pc, Pmma, Ptfe, Soft Plastics, Neoprene And Bituminous Substrates - Not Suitable In Combination With Chlorides (Pools) - Slight Yellowing May Occur When White Sealant Is Exposed To Ultraviolet Rays Surface Preparations And Finishing Application Temperature + 5°C To + 40°C (Applies To Environment And Substrates). All Substrates Must Be Solid, Clean, Dry, And Free Of Grease And Dust. Clean Substrates With Bostik T100 Universal Cleaner. Bostik P590 Seal’n’flex One Plus Adheres Perfectly Without The Use Of A Primer To Most Non Porous Substrates. Porous Substrates To Be Pre-Treated With Bostik T300 Universal Primer. Always Test Adhesion Prior To Application. Use Bostik T500 Finishing Soap To Smooth The Joint. Paintability Bostik P590 Seal’n’flex One Plus Is Paintable With Water Based And Most 2 Component Paints. Synthetic Paints Can Dry Slower.

We Recommend Testing Compatibility With Paint Prior To Application. If Bostik P590 Seal’n’flex One Plus Is Being Painted Over (Not Necessary), We Recommend Slightly Sanding The Sealant And The Junction Surfaces Prior To Use With Scotch-Brite. For The Best Results, We Recommend Painting Within A Few Days Of Application. Cleaning Uncured Material And Tools Can Be Cleaned By Using Bostik T100 Universal Cleaner. Cured Material Can Only Be Mechanically Removed.

Hands Can Be Cleaned With Bostik T150 Cleaning Wipes. Colour(S) - White - Off-White - Light-Grey - Mid-Grey - Dark-Grey - Black Packaging - 300 Ml Cartridge, 12 Per Box - 600 Ml Sausages, 12 Per Box Shelf Life In Unopened Original Packaging Between + 5°C And + 25°C, Shelf Life Is Up To 15 Months From Production Date, Stored In A Dry Place. Health & Safety Product Safety Data Sheet Must Be Read And Understood Before Use. These Are Available On Request And Via The Websites. Certifications - F-Ext-Int-Cc 25lm - Pw-Ext-Int-Cc 25lm - Snjf F25e - A+ French Voc Regulation

COLD APPLIED POLYURETHANE SEALANT

Seal `N' Flex 1 is a low modulus, one component, Class-A polyurethane sealant. When cured it will form a tough, flexible seal capable of cyclic expansion and compression movement of 100% (± 50%) of the original joint width. CLASSIFICATION STANDARDS • CSIRO RILEM Long - Term Sealant Durability Study DBCE Doc.97/196 (M) • DIN 18540 (German) and SJNF (French) approval as a low modulus external joint sealant • AS 4020 Potable Water • ASTM C.920-87 & 98 (USA) as Type S, Grade NS, Class 50, use NT, G, A, M & O as an external joint sealant. • AS 1157-1972 Resistance to fungal growth. Ministry of Agriculture and fisheries New Zealant (Meat, Fish, Game, Poultry - All areas)

Bostik H725 SEAL’N’FLEX FAÇADE is a professional quality sealant for construction and dilatation joints. Bostik H725 SEAL’N’FLEX FAÇADE fulfil BREEAM specifications mentioned in chapter ‘Health and Wellbeing’, Hea 02 Indoor Air Quality, regarding volatile organic compound (VOC) emission levels (products).

APPLICATIONS

Bostik H725 SEAL’N’FLEX FAÇADE was specifically developed as a universal sealant for sealing construction and dilatation joints and joints in pedestrian walkways on most common building materials such as concrete, brickwork, painted wood, enamel, aluminium, stainless steel and a variety of plastics.

DIRECTIONS OF USE

A joint with the correct dimensions is able to absorb movements between building materials. The joint depth should always be in the correct relationship of the joint width. A general rule is the ratio of joint depth to the width of the joint with a joint width up to 10mm is 1:1, with a minimum of 5mm in width and depth. For joints wider than 10mm, the depth is the width divided by 3 plus 6mm