Shiv Sons

Contact no   Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.

#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm  wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm  price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA

Contact no   Pypkote is a pipeline corrosion resistant tape conforming to IS:10221 appendix B specification.It comprises of a tar based polymeric mix supported on a fabric of high tensile strength fibreglass.The polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing.
Tape is terminated on both exteriors by thermofusible HMHDPE Film which aids in the installation process.
Application is fast and easy.
The pipe surface is first cleaned with a wire brush.
IWL CS is applied on pipes immediately after cleaning.
This is to prevent any further accumulation of rust on the pipe.
After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry.
Before adhering the tape to the pipe, it is advisable to gently heat the primercoated pipe by a run of LPG torch.
The bottom surface of the tape is heated by LPG Torch or any heat source.
The tape is wrapped either by spiral or circumference method over the pipe.
By heating the primercoated pipe and by removing the bottom polyethylene from the tape before wrapping, better adhesion between the tape and pipe is obtained.
Overlaps are maintained with a minimum of 12 mm.
A final coat of white wash is done immediately over the entire coated pipe.
Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed.
The procedure for application of tape is the same as bare pipe procedure.
Overlapson each side of the weld joints are to be 50 mm.

#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm  wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm  price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA

Contact no   Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.

#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm  wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm  price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA

Contact no   Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.
#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm  wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm  price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA

Product Description:

APP (Atactic Polypropylene) Membrane is a torch-applied, modified bitumen waterproofing membrane used for protecting roofs, terraces, basements, and wet areas. Designed for Indian weather conditions, APP membranes offer high flexibility, UV resistance, waterproofing efficiency, and long service life.

These rolls are reinforced with polyester or fiberglass for added strength and can be installed on both flat and sloped surfaces using a blowtorch.

• ✔ Torch-applied, seamless waterproofing protection

• ✔ High elongation & tensile strength

• ✔ Resists UV rays, water ingress, and weathering

• ✔ Compatible with concrete, brick, cement plaster, and metal

• ✔ Suitable for horizontal and vertical applications

• ✔ Available in various thicknesses for different project needs

• 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 5 mm

• Standard Roll Sizes:

  • 1m x 10m

  • 1m x 15m

  • 1m x 20m

(Custom roll sizes may be available based on brand or project requirement)

• STP Ltd – SuperThermoLay / Tarfelt APP Membrane

• Asian Paints – SmartCare APP Membrane

• Berger – HomeShield APP Membrane

• Dr. Fixit – Torchshield APP Membrane

• Dr. Seal – APP Modified Bitumen Membrane

• Fosroc – Proofex Torchseal Membrane

• MAK – APP Modified Bituminous Membrane

• IWL – APP Waterproofing Membrane Rolls

• Tikidan India Pvt. Ltd. – Hydrostop APP Membrane

• Concrete Roofs & Sloped Terraces

• Basements & Retaining Walls

• Water Tanks & Podium Slabs

• Bathrooms, Wet Areas, Lift Pits

• Industrial Shed Roofing

• Foundation Waterproofing

• Green Roofs & Landscaped Decks

Delhi, Uttar Pradesh, Bihar, Jharkhand, Madhya Pradesh, Rajasthan, Gujarat, Haryana, Punjab, Uttarakhand, Himachal Pradesh, Chandigarh, Jammu & Kashmir

Product Description:

APP (Atactic Polypropylene) Membrane is a torch-applied, modified bitumen waterproofing membrane used for protecting roofs, terraces, basements, and wet areas. Designed for Indian weather conditions, APP membranes offer high flexibility, UV resistance, waterproofing efficiency, and long service life.

These rolls are reinforced with polyester or fiberglass for added strength and can be installed on both flat and sloped surfaces using a blowtorch.

• ✔ Torch-applied, seamless waterproofing protection

• ✔ High elongation & tensile strength

• ✔ Resists UV rays, water ingress, and weathering

• ✔ Compatible with concrete, brick, cement plaster, and metal

• ✔ Suitable for horizontal and vertical applications

• ✔ Available in various thicknesses for different project needs

• 1 mm, 1.5 mm, 2 mm, 3 mm, 4 mm, 5 mm

• Standard Roll Sizes:

  • 1m x 10m

  • 1m x 15m

  • 1m x 20m

(Custom roll sizes may be available based on brand or project requirement)

• STP Ltd – SuperThermoLay / Tarfelt APP Membrane

• Asian Paints – SmartCare APP Membrane

• Berger – HomeShield APP Membrane

• Dr. Fixit – Torchshield APP Membrane

• Dr. Seal – APP Modified Bitumen Membrane

• Fosroc – Proofex Torchseal Membrane

• MAK – APP Modified Bituminous Membrane

• IWL – APP Waterproofing Membrane Rolls

• Tikidan India Pvt. Ltd. – Hydrostop APP Membrane

• Concrete Roofs & Sloped Terraces

• Basements & Retaining Walls

• Water Tanks & Podium Slabs

• Bathrooms, Wet Areas, Lift Pits

• Industrial Shed Roofing

• Foundation Waterproofing

• Green Roofs & Landscaped Decks

Delhi, Uttar Pradesh, Bihar, Jharkhand, Madhya Pradesh, Rajasthan, Gujarat, Haryana, Punjab, Uttarakhand, Himachal Pradesh, Chandigarh, Jammu & Kashmir

Contact no   Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.

#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm  wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm  price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA