- Home
- ยป
- Our Products
- »
- Pypkote Wrapping Coating
Pypkote Wrapping Coating
Pypkote Anti Corrosion Pipe Wrapping & Coating Tape
Product Brochure
Type | Single Sided |
Brand | IWL India Limited |
Usage/Application | Binding |
Material | Polyester |
Color | Black |
Elongation | 200% |
Manufactured By | IWL india ltd |
Softening Point | 65 to 121 deg C |
Packaging Type | Roll |
Width | 150mm,250mm,500mm,1000mm |
Filler | 20 to 30% |
Contact no Pypkote is a pipeline corrosion resistant tape conforming to IS:10221 appendix B specification.It comprises of a tar based polymeric mix supported on a fabric of high tensile strength fibreglass.The polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing.
Tape is terminated on both exteriors by thermofusible HMHDPE Film which aids in the installation process.
Application is fast and easy.
The pipe surface is first cleaned with a wire brush.
IWL CS is applied on pipes immediately after cleaning.
This is to prevent any further accumulation of rust on the pipe.
After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry.
Before adhering the tape to the pipe, it is advisable to gently heat the primercoated pipe by a run of LPG torch.
The bottom surface of the tape is heated by LPG Torch or any heat source.
The tape is wrapped either by spiral or circumference method over the pipe.
By heating the primercoated pipe and by removing the bottom polyethylene from the tape before wrapping, better adhesion between the tape and pipe is obtained.
Overlaps are maintained with a minimum of 12 mm.
A final coat of white wash is done immediately over the entire coated pipe.
Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed.
The procedure for application of tape is the same as bare pipe procedure.
Overlapson each side of the weld joints are to be 50 mm.
#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA
Additional Information:
- Item Code: 6807
Pypkote Wrapping Coating
Product Brochure
Tape Width | >100 mm |
Brand | IWL India Limited |
Usage/Application | Binding |
Size | 2 inch |
Quantity Per Pack | ROLL |
Tape Length | METER |
Water Proof | YES |
Temperature Range | 65 TO 121 |
Contact no Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.
#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA
Additional Information:
- Item Code: 68079010
- Delivery Time: SAME DAY
- Packaging Details: ROLL
IWL Pypkote 4mm Wrapping Coating Tape
Product Brochure
Tape Length | 10 m |
Tape Thickness | 4 mm |
Color | Black |
Brand | IWL |
Tape Type | Non Adhesive |
Total Thickness | 4mm |
Adhesive Type | Bitumen |
Adhesive Strength | High |
Country of Origin | Made in India |
Contact no Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.
#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA
Pypkote Pipeline Corrosion Resistant Tape
Product Brochure
Tape Width | 4 Inch |
Color | Black |
Brand | IWL |
Tape Type | Non Adhesive |
Softening Point | 65 to 121 DegreeC |
Contact no Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.
#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA
Pypkote Wrapping Coating 4mm
Product Brochure
Tape Length | 10 m |
Tape Thickness | 4 mm |
Color | Black |
Brand | IWL |
Usage/Feature | Pipe Wrapping Tape |
Tape Type | Non Adhesive |
Adhesive Type | Hot Bitumen |
Adhesive Strength | High |
Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the primer coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. By heating the primer coated pipe and by removing the bottom polyethylene from the tape before wrapping, better adhesion between the tape and pipe is obtained. Overlaps are maintained with a minimum of 12 mm. Afinal coat of White Wash is done immediately over the entire coated pipe.
Pypkote
Tape Length | 10 m |
Tape Width | 2 Inch |
Tape Thickness | 4 mm |
MOQ | Roll |
Brand | IWL India Limited |
Usage/Feature | Binding |
Country of Origin | Made in India |
Contact no Pypkote 2 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a film of high tensile strength HMHDPE. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Films which aids in the installation process. Pypkote 2 mm is available in widths of 500mm and 1000mm. Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the CS coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. Overlaps are maintained with a minimum of 12 mm. A final coat of White Wash is done immediately over the entire coated pipe. Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote 2 mm may also be applied as double layer system. In this case a second coat of IWL CS is applied over the first layer of Pypkote 2 mm tape. The CS is allowed to become touch dry. The bottom layer of HMHDPE film is removed from the tape by pulling it manually. The tape is thermofused and wrapped over the primed surface of the first layer like the first application. The overlaps are maintained at a minimum of 12 mm and sealed by thermofusion. Weld Joints are also similarly double wrapped. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover.
#Pypkote installation
#wrapping tape 4mmprice
#pypkote 4mm wrapping tape
#pypkote 4mm suppliers
#pypkote manufacturers in India
#pypkote board suppliers in delhi
#pypkote pipekote wrapping tape manufacturers
#Pypkote 4mm India
#Pypkote 4mm price
#Pypkote 4mm manufacturers
# Pypkote 4mm wrapping tape
#4mm # Pypkote 2mm price
#Pypkote 4mm suppliers in Delhi,Noida,gurgaon
Pypkote 4mm india
# Pypkote 4mm manufacturers in india
# Pypkote 4mm IN INDIA
Bitumen Emulsion RS 1
Product Brochure
Usage/Application | Road Construction |
Penetration Grade | 40/50 |
Type Of Bitumen | Bitumen Emulsion |
Physical State | solid |
Packaging Type | Drum |
Brand | IWL |
Bitumen emulsionis a mixture of fine droplets ofbitumenand water. But as thebitumenis a petroleum product it doesn't mix with water and as it is sticky in nature, it doesn't easily gets disintegrated into fine droplets. To overcome this problem an emulsifier is used
Rapid Setting Emulsion (RS)* Medium Setting Emulsion (MS)*Slow Setting Emulsion (SS)