Shiv Sons

ENIROOF EMB® is a scientific blend of synthetic resins, selected minerals and fillers. ENIROOF EMB® is a protective and waterproof coating. It is a high performance coating that dries to elastic, flexible, impermeable waterproof membrane

Easy and direct (cold applied) application, no pre heating required.  Seamless, no joint.  Provides an impervious waterproofing membrane that protects concrete structure and brick foundations against chloride and sulphate ions present in soils and water.  Corrosion resistant and vapor barrier.

 Useful as protective coating on concrete and brick foundations, retaining walls, timber, metals, etc.  Provides a sandwich membrane in new construction and surface treatment on existing slabs.  Damp – proofing of regular surfaces like concrete and asbestos.  Provides a key for plaster on difficult surfaces.  For waterproofing and protection of structure, Concrete, columns and beam

• It is a scientific blend of pitch free bitumen, synthetic resins, selected minerals and fillers.
• It is a protective and waterproof coating.
• It is a high performance coating that dries to elastic, impermeable waterproof membrane.
• Advantages:

• Easy and direct (cold applied) application, no preheating required.
• Seamless, no joint.
• Provides an impervious waterproofing membrane that protects concrete structure and brick foundations against chloride and sulphate ions present in soils and water.
• Corrosion resistant and vapor barrier.

Surface Preparation:

• The application surface must be clean and free from dust grease and loose particles.
• Surface may be damp but not saturated.
• Apply one coat of Eniroof Black Primer, diluting 1kg Eniroof Black with 1lt water, on well-prepared surface.
• Eniroof Black should be stirred well before use.  
• It is recommended that 1 - 2 coats should be applied depending upon the degree of protection required after the primer coat.
• Brush, roller or sprayer can apply Eniroof Black.

ENIROOF CLEAR is a single pack easy to apply liquidblend of special Urethane resin, Polymer, organic andinorganic compound. It seals and waterproofs the concreteand other absorbent surfaces very effectively. It givesglossy finish whilst enhancing the color of the substrate.

ENIROOF SPR® is a special synthetic resin based waterproof and heat reflective coating. Due to its excellent flexibility and thixotropic nature it is an ideal product for vertical and horizontal surfaces.

Xchem Alfix Coatings is based in India, Delhi, established in 2003. They are manufacturer and provider of Adhesives, Concrete Repairs Solutions, Admixture and Plasticizers. They are focusing on market research and R and D due to that their products are eco-friendly and durable followed the industry standard.

This Star coating waterproofing provides an impervious waterproofing membrane that protects the concrete structure and brick foundations against chloride and sulphate ions present in soils and water.                                                                    Key Features:

• Solid Polyurethane Modified Waterproof Coating.
• Corrosion-resistant and vapour barrier.
• It is a high-performance coating that dries to an elastic, flexible, impermeable waterproof membrane.
• Easy and direct (cold applied) application, no preheating required.
• It is recommended to apply ENIROOF EMB PU in 2coats, at the spread rate of 250.00 ml/Sqmt/coat.
• This is advisable to dilute ENIROOF EMB PU with water or any other suitable solvent to make coating brushable,
  maximum dilution will be 300 ml/kg of ENIROOF EMB PU.(Coverage depends on the porosity of the surface and method of application

ENIROOF SPU is a white, single component anti corrosive, moisture cured waterproof liquid applied coating. It is modified by selective polyurethane polymers

• It is a special synthetic resin based waterproof coating.
• Due to its excellent flexibility and thixotropic nature, it is an ideal product for vertical and horizontal surfaces.
• It is a single pack, very economical and pollution free waterproof coating.
• Because of its white colour it has excellent solar insulation capacity.

Advantages:

• Life and durability of the structure is increased.
• Easy application.
• No mixing or heating required.
• Lightweight compared to conventional roofing systems, thereby loading on the roofs is reduced.
• Provides seamless and joint free seal through out the surface.
• Lower labour cost due to easy, simple and quick application, leading to early completion and time saving.
• Provides insulation due to solar reflection.
• Excellent bonding to most building material.

• It is a scientific blend of synthetic resins, selected minerals and fillers modified with polyurethane.
• It is a protective and waterproof coating.
• It is a high performance coating that dries to elastic, flexible, impermeable waterproof membrane.
• Easy and direct (cold applied) application, no preheating required.
• Provides an impervious waterproofing membrane that protects concrete structure and brick foundations against chloride and sulphate ions present in soils and water.
• Corrosion resistant and vapor barrier.

Advantages:

• Easy and direct (cold applied) application, no pre heating required.
• Seamless, no joint.
• Provides an impervious waterproofing membrane that protects concrete structure and brick foundations against chloride and sulphate ions present in soils and water.
• Corrosion resistant and vapor barrier.

Recommended Uses:

• Useful as protective coating on concrete  nd brick foundations, retaining walls, timber, metals, etc.
• Provides a sandwich membrane in new construction and surface treatment on existing slabs.
• Damp-proofing of regular surfaces like concrete and asbestos.
• Provides a key for plaster on difficult surfaces.
• For waterproofing and protection of structure, concrete, columns and beam.

ENIROOF SPU is a white, single component anti corrosive, moisture cured waterproof liquid applied coating. It is modified by selective polyurethane polymers.

Product DescriptionAQUAGUARD 50% is a single component, 100% ACRYLIC Polymer based polymer in water dispersion consisting of polymer and liquid additives. It can be used as a waterproof membrane for terraces, balconies and roof slabs. It can be used cement mortar patching and resurfacing. Mixed with a cement/sand or gravel combination. It becomes an effective patching and topping mortar having excellent adhesion capabilities and resistance to abrasion It accommodates limited crack movement in underlying surfaces. It develops an excellent bond to most building material hence becoming a part of concrete repair. 


ADVANTAGES 
AQUAGUARD 50% is a ACRYLIC based polymer used for making of cement based waterproofing slurry that is flexible and can be used as coating for control of efflorescence. AQUAGUARD 50% having excellent UV resistance and stability, surface coated with AQUAGUARD 50% can be left exposed to sunlight. AQUAGUARD 50% can be used as bonding agent also. AQUAGUARD 50% is having more than 50 % active ingredients and therefore it is the best cement based waterproof slurry for coating on concrete and all building surfaces required for waterproofing. 
RECOMMENDED USES 

• Water proofing of basements, toilet, terraces, roofs, swimming pools, water tanks, bridge decks, etc. 
• Suitable for general concrete repairs as concrete admixture. It gives excellent bond strength. 
• It can be used for protection of concrete against corrosion, salt attack, etc. 
• As Bonding Agent for plaster, concreting (Old to New), stucco and cement slurry bond coat.

COVERAGE 

1 Lt. AQUAGUARD 50%® mixed as per data sheet will cover appx. 4.5 sqmt – 5.0-sqmt areas in 2 coats depending upon the porosity of the surface. 

SURFACE PREPARATION 

The application surface must be clean and free from dust grease and loose particles. Surface may be damp but not saturated. Prime the prepared surface using AQUAGUARD 50% PRIMER (1 part AQUAGUARD 50%® and 3 parts water) with brush, roller or spray.

AQUACRETE BA 30 is a single component, SBR based, ready to use polymerised bonding agent consisting of polymer and liquid additives. It is used as a bonding agent in old to new concrete applications. It develops an excellent bond to most building material hence becoming a part of concrete repair

ADVANTAGES

AQUACRETE BA 30 is an SBR based polymer used for making of cement based waterproof putty, which is flexible and can be used as crack filler and as a bonding agent in concrete repairs

RECOMMENDED USES

 As a bonding agent for old to new concrete.
 Suitable for general concrete repairs.
 It gives excellent bond strength.
 It can be used for protection of concrete against corrosion, salt attack, etc 

AQUAGUARD 50% is a single component, 100% ACRYLIC Polymer based polymer in water dispersion consisting of polymer and liquid additives. It can be used as a waterproof membrane for terraces, balconies and roof slabs. It can be used cement mortar patching and resurfacing.

AQUACRETE 30%® is a single component, ACRYLIC based polymer, consisting of polymer and liquid additives. It can be used as a waterproof membrane for terraces, balconies and roof slabs. It accommodates limited crack movement in underlying surfaces. It develops an excellent bond to most building material hence becoming a part of concrete repair

ADVANTAGES

AQUACRETE 30%® is a ACRYLIC based polymer used for making of cement based waterproofing slurry that is flexible and can be used as coating for control of efflorescence..

RECOMMENDED USES

Water proofing of basements, toilet, terraces, roofs, swimming pools, water tanks, bridge decks, etc.
 Suitable for general concrete repairs.
 It gives excellent bond strength.
 It can be used for protection of concrete against corrosion, salt attack, etc 

Eniroof Black is a protective and waterproof coating. It is a high performance coating that dries to elastic, flexible, impermeable waterproof membrane.

AQUAGUARD 50% is a single component, 100% ACRYLIC Polymer based polymer in water dispersion consisting of polymer and liquid additives. It can be used as a waterproof membrane for terraces, balconies and roof slabs. It can be used cement mortar patching and resurfacing. Mixed with a cement/sand or gravel combination. It becomes an effective patching and topping mortar having excellent adhesion capabilities and resistance to abrasion It accommodates limited crack movement in underlying surfaces. It develops an excellent bond to most building material hence becoming a part of concrete repair.

AQUAGUARD 1C is a prepackaged cementitious brush; roller orspray applied single component water proofing / damp proofingcoating. It is cement-based polymer modified system, requiringonly addition of water at site to produce a easy to apply slurry.This material exhibits excellent bond strength with reducedpermeability. AQUAGUARD 1C forms a breathableprotective coating. AQUAGUARD 1C protects concrete andmasonry surfaces from water ingress and dampness. It can beused in all types of structures, for existing and new concrete.AQUAGUARD 1C exhibits high Negative side Waterproofproperties apart from high wear resistance, weather resistanceand is suitable to be used as fair facing and damp proofingcompound before application of decorative paints.ADVANTAGES Polymer modification reduces permeability anddusting while increasing bond, tensile and flexuralstrength. Non-toxic, Breathable Coating Very Effective from Negative side applications as anunderlay. For interior or exterior use. Excellent wear resistance. User friendly-low labour cost.RECOMMENDED USES Water proofing of basements, toilet, terraces, roofs,swimming pools, water tanks, Interior and exteriormasonry / concrete walls. As treatment against rising dampness and concreterefurbishment. As a water proofing and protective coating onconcrete and plaster from Negative side. DIY product for water proofing / damp proofing.ApplicationSurface Preparation: Concrete must be clean and rough. All oil,dirt, debris, paint and unsound concrete must be removed. Thesurface can be prepared mechanically using sandblasting, shotblasting or scarifier, which will give a slight surface profile. Thefinal step in cleaning should be complete removal of all residueswith a vacuum cleaner or by pressure washing.Prior to application, the surface should be pre-soaked withclean water, excess standing water should be removed.